| Overview | Package | Class | Deprecated | Help |
| Properties | |
|---|---|
| addressType |
type=int default=system Displayed(tab/group)=Address Type (Interface Properties) enums= 1: interface 2: system |
| autoRxIpv4AdminState |
Specifies whether automatic IPv4 Rx targeted sessions are created or not.
When this object is administratively up, automatic targeted sessions are created
to the PQ router ID of each route that contains remote LFA information.
When this object is administratively down, automatic targeted sessions are not
created to the PQ router IDs.
type=netw.AdministrativeState default=mplsDown Displayed(tab/group)=Rx Administrative State (Targeted Peer Properties.General/IPv4 Automatic TLDP) |
| autoRxIpv4Tunneling |
Specifies whether tunneling of unicast LDP FECs over tunnels is enabled for the
automatic IPv4 Rx targeted sessions.
type=boolean default=false Displayed(tab/group)=Rx LDP FEC Tunneling (Targeted Peer Properties.General/IPv4 Automatic TLDP) |
| autoTxIpv4AdminState |
Specifies whether automatic IPv4 Tx targeted sessions are created or not.
When this object is administratively up, automatic targeted sessions are created
to the PQ router ID of each route that contains remote LFA information.
When this object is administratively down, automatic targeted sessions are not
created to the PQ router IDs.
type=netw.AdministrativeState default=mplsDown Displayed(tab/group)=Tx Administrative State (Targeted Peer Properties.General/IPv4 Automatic TLDP) |
| autoTxIpv4Tunneling |
Specifies whether tunneling of unicast LDP FECs over tunnels is enabled for the
automatic IPv4 Tx targeted sessions.
type=boolean default=false Displayed(tab/group)=Tx LDP FEC Tunneling (Targeted Peer Properties.General/IPv4 Automatic TLDP) |
| backoffTime |
type=int access=read-only default=15 minimum=1 maximum=2592000 units=seconds Displayed(tab/group)=Backoff Time (Common) |
| backupSRTunnel |
Specifies whether fast re-route of LDP tunnel via a segmented-routing tunnel is enabled or disabled.
This property can only be enabled if Fast Re-route is enabled.
type=boolean default=false Displayed(tab/group)=Backup SR Tunnel (Common) |
| bfd.BfdOnLspSession-Set |
type=Children-Set |
| classForwarding |
Indicates whether class forwarding is enabled or not for LDP-over-RSVP.
type=boolean default=false Displayed(tab/group)=Class Forwarding (Common) |
| classForwardingMode |
Indicates whether class forwarding is enabled for LER, LSR or both. It has no effect unless
classForwarding is enabled.
type=int default=1 Displayed(tab/group)=Class Forwarding Mode (Common) enums= 1: lsr - LSR 2: ler - LER 3: lsr_ler - LSR and LER |
| controlMode |
type=int access=read-only default=unspecified Displayed(tab/group)=Control Mode (Common) enums= 1: ordered 2: independent |
| deaggregateFec |
type=generic.TruthValue access=read-only default=false Displayed(tab/group)=De-aggregate FEC (Interface Properties) |
| distributionMode |
type=int access=read-only default=unspecified Displayed(tab/group)=Distribution Mode (Common) enums= 1: downstreamOnDemand 2: downstreamUnsolicited |
| enableTargetedHelloReduction |
The Enable Hello Reduction parameter specifies whether IPv4 hello reduction is enabled for the targeted peer.
When hello reduction is enabled, hello messages are suppressed when a targeted LDP session is established
between two peers. If the parameter is disabled while the targeted LDP session to the peer is operationally
up, the change in the hold time will take effect only when the targeted LDP session is reestablished.
type=generic.TruthValue default=false Displayed(tab/group)=Enable Hello Reduction (Targeted Peer Properties.General/IPv4 Timer Control) |
| entropyLblCapability |
Specifies whether entropy label capability is enabled or not on the LDP node.
type=boolean default=false Displayed(tab/group)=Enable Entropy Label Capability (Common) |
| fastReroute |
The value of fastReroute specifies whether fast re-route of LDP
tunnel is enabled or disabled.
type=boolean default=false Displayed(tab/group)=Fast Re-route (Common) |
| fwdStateHoldingTime |
Enable/disable TTL propagation of transit IP packets.
type=int default=120 minimum=15 maximum=1800 units=seconds Displayed(tab/group)=Forward State Holding Time (Common/Graceful Restart) |
| generateBasicFecOnly |
Specifies whether the root node will generate a non recursive FEC even if the root node
is resolved via BGP.
When the value is set to 'true', a non-recursive FEC will be generated towards the root node.
When the value is set to 'false', a recursive FEC will be generated towards the root node.
This configuration is applicable to FECs whose root address is in the GRT and that have a
generic LSP identifier as the opaque type.
type=boolean default=false Displayed(tab/group)=Generate Basic FEC Only (Common) |
| gracefulRestart |
This property configures the graceful restart helper.
type=boolean default=false Displayed(tab/group)=Enforce Graceful Restart (Common) |
| helloTimeout |
type=int default=15 minimum=3 maximum=65535 units=seconds Displayed(tab/group)=Hello Timeout (Interface Properties/IPv4 Timer Control) |
| helloTimeoutFactor |
type=int default=3 minimum=1 maximum=255 Displayed(tab/group)=Hello Factor (Interface Properties/IPv4 Timer Control) |
| hopLimit |
type=int access=read-only default=255 minimum=0 maximum=255 Displayed(tab/group)=Hop Limit (Common) |
| implicitNullLabel |
The value of this property specifies whether or not to signal implicit null values.
type=boolean default=false Displayed(tab/group)=Enable Implicit Null Label (Common) |
| importBgpMvpnRoutes |
Specifies whether LDP will import BGP MVPN inter-AS routes.
type=boolean default=false Displayed(tab/group)=MVPN Routes (Common/Import BGP PMSI Routes) |
| importBgpMvpnRoutesNoExportComm |
Specifies whether LDP will import BGP MVPN intra-AS routes.
type=boolean default=false Displayed(tab/group)=MVPN No Export Community Routes (Common/Import BGP PMSI Routes) |
| ipv4LsrInterop |
Specifies if interoperability with legacy IPv4 LSR implementations which do not comply to the
processing of Hello TLVs with the U-bit set is allowed.
type=boolean default=false Displayed(tab/group)=Legacy IPv4 LSR Interoperability Support (Common) |
| ipv6AddressType |
Specifies the source of the transport address to be used when setting up the LDP TCP sessions.This value is only applicable to LDP IPv6 interfaces.
type=int default=system Displayed(tab/group)=IPv6 Address Type (Interface Properties) enums= 1: interface 2: system |
| ipv6EnableTargetedHelloReduction |
The Enable Hello Reduction parameter specifies whether IPv6 hello reduction is enabled for the targeted peer.
When hello reduction is enabled, hello messages are suppressed when a targeted LDP session is established
between two peers. If the parameter is disabled while the targeted LDP session to the peer is operationally
up, the change in the hold time will take effect only when the targeted LDP session is reestablished.
type=generic.TruthValue default=false Displayed(tab/group)=Enable Hello Reduction (Targeted Peer Properties.General/IPv6 Timer Control) |
| ipv6HelloTimeout |
Specifies the time interval, in seconds, that LDP waits before declaring a neighbor to be down. It cannot be set to a value that is less than 3 times the hello time.
This value is only applicable to LDP IPv6 interfaces
type=int default=15 minimum=3 maximum=65535 units=seconds Displayed(tab/group)=Hello Timeout (Interface Properties/IPv6 Timer Control) |
| ipv6HelloTimeoutFactor |
Specifies the value by which the hello timeout should be divided to give the hello time i.e. the time interval, in seconds,
between LDP Hello messages.This value is only applicable to LDP IPv6 interfaces.
type=int default=3 minimum=1 maximum=255 Displayed(tab/group)=Hello Factor (Interface Properties/IPv6 Timer Control) |
| ipv6KATimeout |
Specifies the time interval, in seconds, that LDP waits before tearing down a session. Generally the value to be configured should be 3 times the keepalive time.
This value is only applicable to LDP IPv6 interfaces.
type=int default=30 minimum=3 maximum=65535 units=seconds Displayed(tab/group)=Keep-Alive Timeout (Interface Properties/IPv6 Timer Control) |
| ipv6KATimeoutFactor |
Specifies the value by which the keepalive timeout should be divided to give the keepalive time i.e. the time interval, in seconds,
between LDP keepalive messages. This value is only applicable to LDP IPv6 interfaces.
type=int default=3 minimum=1 maximum=255 Displayed(tab/group)=Keep-Alive Factor (Interface Properties/IPv6 Timer Control) |
| ipv6LsrId |
Specifies the IPv6 Label Switch Router (LSR) identifier which is used as first 16 bytes or
the Router Id component of the Label Distribution Protocol (LDP) identifier.
type=string access=read-only default=0:0:0:0:0:0:0:0 minimum=15 maximum=39 Displayed(tab/group)=IPv6 LSR ID (Common) |
| ipv6OperDownReasonCode |
Indicates the reason due to which the IPv6 LDP instance is operationally down
type=ldp.LdpOperDownReasonCode access=read-only default=operUp Displayed(tab/group)=IPv6 Operational State Down Reason |
| ipv6OperationalState |
Specifies the current operational state of IPv6 LDP instance.
type=netw.OperationalState access=read-only default=unknown Displayed(tab/group)=IPv6 Operational State |
| ipv6ResolvePrefixOverShortcut |
Specifies whether an IPv6 prefix FEC is resolved over an IGP shortcut.
If the value is 'true', then resolution is allowed.
If value is 'false', then resolution is not allowed.
type=boolean default=false Displayed(tab/group)=IPv6 Prefix FEC IGP Shortcut Resolved (Targeted Peer Properties.General/IPv6 Prefix FEC) |
| ipv6TargetedHelloFactor |
Specifies the value by which the hello timeout should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages.
This value is only applicable to IPv6 LDP targeted peer.
type=int default=3 minimum=1 maximum=255 Displayed(tab/group)=Hello Factor (Targeted Peer Properties.General/IPv6 Timer Control) |
| ipv6TargetedHelloReductionFactor |
The Hello Reduction Factor parameter specifies the number of hello messages that are sent within the
hold time interval when IPv6 hello reduction is enabled.
type=int default=3 minimum=3 maximum=20 Displayed(tab/group)=Hello Reduction Factor (Targeted Peer Properties.General/IPv6 Timer Control) |
| ipv6TargetedHelloTimeout |
Specifies the time interval, in seconds, that LDP waits before declaring a neighbor to be down.It cannot be set to a value that is less than 3 times the hello time.
This value is only applicable to IPv6 LDP targeted peer.
type=int default=45 minimum=3 maximum=65535 units=seconds Displayed(tab/group)=Hello Timeout (Targeted Peer Properties.General/IPv6 Timer Control) |
| ipv6TargetedKAFactor |
Specifies the value by which the keepalive timeout should be divided to give the keepalive time i.e. the time interval, in seconds,
between LDP keepalive messages.This value is only applicable to IPv6 targeted LDP peer.
type=int default=4 minimum=1 maximum=255 Displayed(tab/group)=Keep-Alive Factor (Targeted Peer Properties.General/IPv6 Timer Control) |
| ipv6TargetedKATimeout |
Specifies the time interval, in seconds, that LDP waits before tearing down a session. Generally the value to be configured should be 3 times the keepalive time.
This value is only applicable to IPv6 targeted LDP peer.
type=int default=40 minimum=3 maximum=65535 units=seconds Displayed(tab/group)=Keep-Alive Timeout (Targeted Peer Properties.General/IPv6 Timer Control) |
| keepAliveTimeout |
type=int default=30 minimum=3 maximum=65535 units=seconds Displayed(tab/group)=Keep-Alive Timeout (Interface Properties/IPv4 Timer Control) |
| keepAliveTimeoutFactor |
type=int default=3 minimum=1 maximum=255 Displayed(tab/group)=Keep-Alive Factor (Interface Properties/IPv4 Timer Control) |
| labelWithdrawalDelay |
Specifies the time interval, in seconds, LDP will delay for the withdrawal of
FEC-label binding it distributed to its neighbours when FEC is
de-activated. When the timer expires, LDP then sends a label withdrawal for the FEC to all its
neighbours. This is applicable only to LDP transport tunnels (ipv4 prefix FECs) and is not
applicable to Pseudowires(service FECs).
The valid range is 3 to 120 seconds.
A value of 0 indicates that labelWIthdrawalDelay is disabled.
type=int default=0 minimum=0 maximum=120 units=seconds Displayed(tab/group)=Label Withdrawal Delay (Common) |
| ldp.AccountingFecPrefix-Set |
type=Children-Set |
| ldp.AggregatePrefixPolicy-Set |
type=Children-Set |
| ldp.AuthenticationKey-Set |
type=Children-Set |
| ldp.BfdOnLspPrefixList-Set |
type=Children-Set |
| ldp.DiscoveredFec-Set |
type=Children-Set |
| ldp.Ecmp-Set |
type=Children-Set |
| ldp.Interface-Set |
type=Children-Set |
| ldp.Peer-Set |
type=Children-Set |
| ldp.PeerTransport-Set |
type=Children-Set |
| ldp.Session-Set |
type=Children-Set |
| ldp.SiteExportPolicy-Set |
type=Children-Set |
| ldp.SiteImportPolicy-Set |
type=Children-Set |
| ldp.SiteMulticastImportPolicy-Set |
type=Children-Set |
| ldp.SiteTunnelTableExportPolicy-Set |
type=Children-Set |
| ldp.SiteTunnelTableImportPolicy-Set |
type=Children-Set |
| ldp.StaticFec-Set |
type=Children-Set |
| ldp.TargetedPeer-Set |
type=Children-Set |
| ldp.TargetedSessionExportPolicy-Set |
type=Children-Set |
| ldp.TargetedSessionImportPolicy-Set |
type=Children-Set |
| ldpDynamicCapable |
Specifies whether dynamic capability negotiation is supported or not in LDP sessions associated
with the LDP instance. When 'true', the LDP instance supports dynamic capability negotiation.
type=boolean access=read-only default=false Displayed(tab/group)=Dynamic Capability Negotiation (Common) |
| localTtlPropagate |
Enable/disable TTL propagation of locally generated IP packets.
type=boolean default=true Displayed(tab/group)=Shortcut Local TTL Propagate (Common/TTL Propagate) |
| loopDetectCapable |
type=int access=read-only default=none Displayed(tab/group)=Loop Detection (Common) enums= 1: none 2: other 3: hopCount 4: pathVector 5: hopCountAndPathVector |
| lsrId |
type=string access=read-only default=0.0.0.0 minimum=7 maximum=15 Displayed(tab/group)=LSR ID (Common) |
| mCastUpstreamAsbrFrr |
Specifies whether the local leaf will do MOFRR to the multiple ASBRs or not.
When the value is set to 'false' only IGP MOFRR in the local AS is allowed.
type=boolean default=false Displayed(tab/group)=MCast Upstream ASBR Fast Re-route (Common) |
| mCastUpstreamFrr |
Specifies whether mLDP fast upstream switchover feature is enabled or not for the LDP instance.
type=boolean default=false Displayed(tab/group)=MCast Upstream Fast Re-route (Common) |
| maxBackoffTime |
type=int access=read-only default=120 minimum=1 maximum=2592000 units=seconds Displayed(tab/group)=Maximum Backoff Time (Common) |
| maxEcmpRoutes |
Specifies the maximum ECMP routes value for LDP.
type=int default=32 minimum=1 maximum=64 Displayed(tab/group)=Maximum ECMP routes |
| maximumRecoveryTime |
This property configures the maximum recovery time (in seconds).
type=int default=120 minimum=15 maximum=1800 units=seconds Displayed(tab/group)=Maximum Recovery Time (Common/Graceful Restart) |
| mpMBBCapable |
Whether Multipoint (MP)
Make-Before-Break (MBB) capability is supported in the ldp instance or not. When
the value is true means the ldp instance is MP MBB capable
type=boolean access=read-only default=false Displayed(tab/group)=Multi Path Make Before Break Capable (Common/Graceful Restart) |
| mpMBBTime |
The maximum time a Multi Point (MP) transit node must wait
before switching over to a new path if the new node does not
send Make Before Break (MBB) Tag Length Value (TLV) to inform
of the availability of the data plane.
type=int default=3 minimum=0 maximum=10 units=seconds Displayed(tab/group)=Multi Path Make Before Break Time (Common/Graceful Restart) |
| neighborLivenessTime |
This property configures the neighbor liveness time (in seconds).
type=int default=120 minimum=5 maximum=300 units=seconds Displayed(tab/group)=Neighbor Liveness Time (Common/Graceful Restart) |
| operDownReasonCode |
Indicates the reason due to which the IPv4 LDP instance is operationally down
type=ldp.LdpOperDownReasonCode access=read-only default=operUp Displayed(tab/group)=Operational State Down Reason |
| operationalEcmp |
Specifies the operational ECMP value. This value is the smaller of the configured router ECMP value
and the configured LDP max ECMP routes value.
type=int access=read-only Displayed(tab/group)=Operational ECMP |
| p2mpCapable |
Whether Point-to-Multipoint (P2MP) FEC
capability is supported in the ldp instance or not. When the value is true means the ldp
instance is P2MP capable.
type=boolean access=read-only default=false Displayed(tab/group)=P2MP Capable (Common) |
| pathVectorLimit |
type=int access=read-only default=255 minimum=0 maximum=255 Displayed(tab/group)=Path Vector Limit (Common) |
| preferMcastTunnelInTunnel |
Specifies the preference of targeted LDP session over a link LDP session
for both the upstreamand downstream resolution of a multicast FEC. If this
value is 'true', then targeted session is preferred and if the value is 'false'
then link session is preferred.
type=boolean default=false Displayed(tab/group)=Prefer Multicast Tunnel-in-Tunnel (Common) |
| preferProtocolStitching |
Specifies whether stitching to another protocol is preferred over route resolution. If
the value is 'true', then protocol stitching is preferred. If value is
'false', then route resolution is preferred
type=boolean default=false Displayed(tab/group)=Prefer Protocol Stitching (Common) |
| preferTransportFrr |
The value of preferTransportFrr indicates whether the FRR of the outer protocol is preferred or not.
If the value is 'true' then the FRR of outer protocol is preferred.
If the value is 'false' then LDP FRR is preferred.
type=boolean default=false Displayed(tab/group)=Prefer Transport FRR (Common) |
| preferTunnelInTunnel |
Indicates whether LDP tunnel-in-tunnel is preferred over a link-level LDP tunnel.
type=boolean default=false Displayed(tab/group)=Prefer Tunnel-in-Tunnel (Common) |
| propagatePolicy |
type=int access=read-only default=system Displayed(tab/group)=Propagate Policy (Interface Properties) enums= 1: interface 2: system 3: all 4: none |
| protocolVersion |
type=int access=read-only default=0 Displayed(tab/group)=Protocol Version (Common) |
| reconnectTime |
Enable/disable TTL propagation of transit IP packets.
type=int default=120 minimum=15 maximum=1800 units=seconds Displayed(tab/group)=Reconnect Time (Common/Graceful Restart) |
| resolveRoot |
Specifies whether multicast FECs will use the unicast route table or the multicast route table
for resolution.
type=int default=unicastRtm Displayed(tab/group)=Resolve Root (Common) enums= 1: unicastRtm - Unicast RTM 2: multicastRtm - Multicast RTM |
| retentionMode |
type=int access=read-only default=unspecified Displayed(tab/group)=Retention Mode (Common) enums= 1: conservative 2: liberal |
| routePreference |
type=int access=read-only default=9 minimum=1 maximum=255 Displayed(tab/group)=Route Preference (Interface Properties) |
| sysIpGlobalExportPolicy |
Specifies whether or not creation of system IP FECs is affected by the LDP global export
policy. When enabled, the global export policy is consulted when determining whether or not
to create a FEC for the system IP address(es). When disabled, FECs are unconditionally
created for the system IP address(es).
type=boolean default=false Displayed(tab/group)=System IP in Global Export Policy (Common) |
| targetedHelloFactor |
type=int default=3 minimum=1 maximum=255 Displayed(tab/group)=Hello Factor (Targeted Peer Properties.General/IPv4 Timer Control) |
| targetedHelloReductionFactor |
The Hello Reduction Factor parameter specifies the number of hello messages that are sent within the
hold time interval when IPv4 hello reduction is enabled.
type=int default=3 minimum=3 maximum=20 Displayed(tab/group)=Hello Reduction Factor (Targeted Peer Properties.General/IPv4 Timer Control) |
| targetedHelloTimeout |
type=int default=45 minimum=3 maximum=65535 units=seconds Displayed(tab/group)=Hello Timeout (Targeted Peer Properties.General/IPv4 Timer Control) |
| targetedKeepAliveFactor |
type=int default=4 minimum=1 maximum=255 Displayed(tab/group)=Keep-Alive Factor (Targeted Peer Properties.General/IPv4 Timer Control) |
| targetedKeepAliveTimeout |
type=int default=40 minimum=3 maximum=65535 units=seconds Displayed(tab/group)=Keep-Alive Timeout (Targeted Peer Properties.General/IPv4 Timer Control) |
| targetedPassiveMode |
type=generic.TruthValue access=read-only default=false Displayed(tab/group)=Passive Mode (Targeted Peer Properties.General) |
| targetedSessions |
type=generic.TruthValue default=true Displayed(tab/group)=Targeted Sessions Allowed (Common) |
| transitTtlPropagate |
Enable/disable TTL propagation of transit IP packets.
type=boolean default=true Displayed(tab/group)=Shortcut Transit TTL Propagate (Common/TTL Propagate) |
| tunnelDownDampTime |
type=int default=3 minimum=0 maximum=20 units=seconds Displayed(tab/group)=Tunnel Down Damp Time (Common) |
| tunnelTablePreference |
Specifies the tunnel preference assigned to LDP tunnels for address FECs.
type=int default=9 minimum=1 maximum=255 Displayed(tab/group)=Tunnel Table Preference (Common) |
| weightedEcmp |
"The value of weightedEcmp specifies whether or not LDP will use weighted-ECMP when programming
LDP IGP-shortcut FECs. The IGP-shortcut routes must also contain weighting information for the
weighted-ECMP to be used."
type=boolean default=false Displayed(tab/group)=Weighted-Ecmp (Common) |
| Overridden Properties | |
|---|---|
| administrativeState |
default=mplsUp |
| displayedName |
default=LDP |
| Properties inherited from rtr.ProtocolSite |
|---|
| creationOrigin, serviceId, serviceType, subscriberId |
| Properties inherited from rtr.RouterSite |
|---|
| routerId, routerName, routingInstancePointer |
| Properties inherited from netw.NetworkSite |
|---|
| displayedName, siteId, siteName |
| Properties inherited from netw.SubnetworkConnection |
|---|
| domain |
| Properties inherited from netw.Connection |
|---|
| administrativeState, application, connectionId, operationalState |
| Properties inherited from ManagedObject |
|---|
| actionMask, children-Set, deploymentState, isFaultSquelched, name, objectFullName, selfAlarmed |
| Methods |
|---|
deployer
: Deployer - the deployment state
synchronousDeploy
: boolean - (Optional) Specify whether to block until the changes have been fully deployed to the network. A value of "true" means to block. A value of "false" means to return immediately. Default: false (asynchronous)
clearOnDeployFailure
: boolean - (Optional) Specify whether to clear any failed deployers. A value of "true" means to clear. A value of "false" means to leave the failed deployer. Default: false
deployRetries
: int - (Optional) The number of times to attempt re-deployment during synchronous deployment. This parameter is meaningless in the asynchronous case. Default: 0
deployRetryInterval
: long - (Optional) The number of milliseconds to wait between deployment retries. This parameter is meaningless in the asynchronous case. Default: 0
taskDescription
: string - (Optional) A user friendly description of what the operation does. This information will be used by the task manager.
instanceFullName
: string - the full name of the object.
configInfo
: generic.CommonManagedContainmentEntityConfigurationInformation -
continueOnFailure
: continueOnFailure - (Optional) Continue processing requests in this stream if an exception occurs, unless the request is invalid. Default: false
objectFullName
: string -
ldp.Site.configureException
filter
: FilterHolder -
resultFilter
: ResultFilter - (Optional) Filter for narrowing down the information returned per object
continueOnFailure
: continueOnFailure - (Optional) Continue processing requests in this stream if an exception occurs, unless the request is invalid. Default: false
infoList
: List (generic.CommonManagedEntityInformation) - | Methods inherited from rtr.ProtocolSite |
|---|
| shutDown, turnUp |