sas.ArchivedPing (NSP Network Functions Manager - Packet25.8)

sas
ArchivedPing

Archived test. Represents a ping operation. Ping operation is usually used to verify connectivity between 1 or more sites.

Inheritance Hierarchy
- ManagedObject
  - sas.AbstractTest
    - sas.ArchivedTest
      - sas. ArchivedPing

Direct Subclasses
- ancp.ArchivedAncpLoopback, atm.ArchivedAtmPing, bier.ArchivedBierPing, icmp.ArchivedDnsPing, icmp.ArchivedIcmpPing, mpls.ArchivedLspPing, mpls.ArchivedP2MPLspPing, multicast.ArchivedMfibPing, multicast.ArchivedMrinfo, sas.ArchivedVxlanPing, service.ArchivedCpePing, service.ArchivedMacPing, service.ArchivedSitePing, svt.ArchivedMtuPing, svt.ArchivedTunnelPing, svt.ArchivedVccvPing, vprn.ArchivedVprnPing

public abstract class ArchivedPing

Displayed Name=Archived Ping

Properties
assurance	type=sas.TestAdminState access=read-only
maxHistoryRows	> The maximum number of rows allowed in the node's probe result table. The node will remove the oldest entry in the table to allow the addition of a new history row. A value of 0 for this object disables creation of tmnxOamPingHistoryTable entries. DEPRECATED: 8.0 R5 - OBSOLETE: Never Supported type=long access=read-only
packetFailureThreshold	The Packet Failure Threshold parameter specifies the number of times a probe can fail before the test fails. The parameter has no effect if the value is higher than the parameter value. The range is 0 to 15. The default is 1. type=int access=read-only Displayed(tab/group)=Probe Failure Threshold (Results Configuration)
packetInterval	Specifies the number of seconds to wait before sending the next probe. Units can be set to Centiseconds using packetIntervalUnits for Cfm TwoWay Delay and Two Way SLM tests on CPM3 7x50 devices type=int access=read-only Displayed(tab/group)=Packet Interval (Test Parameters/Execution Details)
packetSize	The size of the packets to send. type=int access=read-only
packetTimeout	Specifies the number of seconds to wait for the response of a sent probe. type=int access=read-only Displayed(tab/group)=Probe Timeout (Test Parameters/Execution Details)
packetsToSend	The number of probes to send. type=int access=read-only Displayed(tab/group)=Number of Test Probes (Test Parameters/Execution Details)
testFailureThreshold	The Test Failure Threshold parameter specifies the number of test failures that occur before an NE sends a trap about the test failure. The range is 0 to 15. The default is 1. type=int access=read-only Displayed(tab/group)=Test Failure Threshold (Results Configuration)
trapGenerationPolicy	Specifies when the node sends traps while executing the test. type=sas.PingTrapGenerationPolicy access=read-only Displayed(tab/group)=Trap Generation (Results Configuration)

Overridden Properties
id	The identifier for the STM test.

Properties inherited from sas.ArchivedTest
accountingFiles, accountingPolicyObjectPointer, continuousExec, ethernetSwitchCardId, fromNodeId, nePersistent, neSchedulable, neTestIndex, neTestOwner, nmUser, originatingTest, ownerType, testResultStorage, testSuite, testSuiteId, testSuiteTestedEntity, testType, testedObject

Properties inherited from sas.AbstractTest
administrativeState, description, displayedName, failures, globalId, id, lastRunResult, runs, weight

Properties inherited from ManagedObject
actionMask, children-Set, deploymentState, isFaultSquelched, name, objectFullName, selfAlarmed

Methods inherited from sas.AbstractTest
execute, stop