| Overview | Package | Class | Deprecated | Help |
| Properties | |
|---|---|
| actualPmMode |
type=vwm.IfActualPmModeType access=read-only Displayed(tab/group)=Actual Performance Monitoring Mode (/TLU 9M Specifics) |
| apAins |
If the user has set Port AINS to true, the port admin state is set to up by the system.
If the port admin state has been set up or down, Port AINS is set to false by the system,
unless the user had specified admin up and Port AINS true.
Disabling Port AINS against a client port of an OT card may result in disabling Port AINS against
the line port of that OT card.
type=boolean Displayed(tab/group)=Port AINS (/AINS) |
| apAinsDebounceTime |
This attribute must be set in multiples of 60s.
It is equal to System AINS Debounce Time when
Port AINS Use System Default is true. Setting
the Port AINS Debounce Time and Port AINS Use
System Default to true in the same set request
is restricted.
Current configurable range: 1m to 96h 0m.
0 is a valid value.
type=string units=HH:MM Displayed(tab/group)=AINS Timer (/AINS) |
| apAinsDebounceTimeRemaining |
Number of seconds until the Port AINS DebounceTime expires.
If Port AINS is false or Port AINS Debounce Time is 0, the value of this attribute will be 0.
type=string access=read-only units=HH:MM Displayed(tab/group)=AINS Countdown (/AINS) |
| autoNegotiate |
type=int default=true Displayed(tab/group)=Auto-negotiate (/MAU) enums= 0: notApplicable - N/A (not selectable) 1: true - True 2: false - False |
| connectorPresent |
type=boolean access=read-only default=true Displayed(tab/group)=Connector Present (/Port Details) |
| duplex |
type=int default=1 Displayed(tab/group)=Duplex (/MAU) enums= 1: fullDuplex - Full-Duplex 2: halfDuplex - Half-Duplex |
| etherSpeed |
type=int default=speed100 minimum=0 maximum=5000 units=mbps Displayed(tab/group)=Speed (/MAU) enums= 0: notApplicable - N/A (not selectable) 1: speed10 - 10 Mbps 2: speed100 - 100 Mbps |
| highSpeed |
An estimate of the interface's current bandwidth in units
of 1,000,000 bits per second. If this object reports a
value of `n' then the speed of the interface is somewhere in
the range of `n-500,000' to `n+499,999'. For interfaces
which do not vary in bandwidth or for those where no
accurate estimation can be made, this object should contain
the nominal bandwidth. For a sub-layer which has no concept
of bandwidth, this object should be zero.
type=int access=read-only default=100 units=bps Displayed(tab/group)=High Speed (/Port Details) |
| ifCapability |
type=vwm.TropicVwmMsIfCapabilityBits access=read-only Displayed(tab/group)=Port Capability (/Port Details) |
| ifPmCvSesThreshold10B |
type=long default=0 minimum=0 maximum=65535 Displayed(tab/group)=CvSesThreshold10B (/TLU 9M Specifics), CvSesThreshold10B (/TLU 200 Specifics) |
| ifPmCvSesThreshold66B |
type=long default=0 minimum=0 maximum=65535 Displayed(tab/group)=CvSesThreshold66B (/TLU 9M Specifics), CvSesThreshold66B (/TLU 200 Specifics) |
| ifPmSesMonitoringMode |
type=vwm.IfPmSesMonitoringModeType access=read-only Displayed(tab/group)=SesMonitoringMode (/TLU 9M Specifics), SesMonitoringMode (/TLU 200 Specifics) |
| interfaceRole |
Interface Role.
type=vwm.VwmMsIfRole Displayed(tab/group)=Interface Role (/Port Details) |
| interfaceType |
The type of interface. Additional values for ifType are
assigned by the Internet Assigned Numbers Authority (IANA),
through updating the syntax of the IANAifType textual
convention.
type=vwm.IANAifType access=read-only Displayed(tab/group)=Interface Type (/Port Details) |
| l1FarEndAddress |
"Access port far end address."
type=string default= Displayed(tab/group)=Far End Address (/Far End Details) |
| l1FarEndAddressConnFrom |
"Access port far end connected from address."
type=string default= Displayed(tab/group)=Connected From Far End Address (/Far End Details) |
| l1FarEndIfIndex |
"Access port far end interface index."
type=Pointer Displayed(tab/group)=Far End Port (/Far End Details) |
| l1FarEndIfIndexConnFrom |
"Access port far end connected from interface index."
type=Pointer Displayed(tab/group)=Connected From Far End Port (/Far End Details) |
| l1FarEndType |
"Access port far end type."
type=vwm.AccessPortFarEndType default=notConnected Displayed(tab/group)=Far End Type (/Far End Details) |
| l1FarEndTypeConnFrom |
"Access port far end connected from type."
type=vwm.AccessPortFarEndType default=notConnected Displayed(tab/group)=Connected From Far End Type (/Far End Details) |
| l2FarEndIfIndex |
"Access port Layer 2 far end interface index."
type=Pointer access=read-only Displayed(tab/group)=L2 Far End Port (/L2 Far End Details) |
| l2FarEndMacAddress |
"Access port Layer 2 far end MAC address."
type=MacAddress access=read-only default=00-00-00-00-00-00 Displayed(tab/group)=L2 Far End MacAddress (/L2 Far End Details) |
| loopbackStatus |
"Interface Facility Loopback."
type=generic.EnabledDisabled Displayed(tab/group)=Facility LoopBack Status (/Loop Back) |
| pir |
type=int default=10 minimum=1 maximum=100 units=Mbps Displayed(tab/group)=PIR (/Userdata) |
| pmMode |
type=vwm.IfPmModeType default=basic Displayed(tab/group)=Performance Monitoring Mode (/TLU 9M Specifics) |
| popoutervlan |
type=int default=true Displayed(tab/group)=Pop Outer Vlan (/Userdata) enums= 1: true - True 2: false - False |
| portDirection |
Port Direction
type=vwm.PortDirection Displayed(tab/group)=Port Direction (/Far End Details) |
| portDirectionCapability |
Port Direction Capability.
type=vwm.PortDirectionCapability access=read-only Displayed(tab/group)=Port Direction Capability (/Far End Details) |
| portSpeed |
ifSpeed - An estimate of the interface's current
bandwidth in bits per second. For interfaces
which do not vary in bandwidth or for those
where no accurate estimation can be made, this
object should contain the nominal bandwidth. If
the bandwidth of the interface is greater than
the maximum value reportable by this object then
this object should report its maximum value
(4,294,967,295) and ifHighSpeed must be used to
report the interace's speed. For a sub-layer
which has no concept of bandwidth, this object
should be zero.
type=int access=read-only default=100 units=bps Displayed(tab/group)=Port Speed (/Port Details) |
| pvid |
type=int default=0 minimum=0 maximum=4079 Displayed(tab/group)=Pvid (/Userdata) |
| rflmLabel |
RFLM Interface label.
type=string minimum=0 maximum=64 Displayed(tab/group)=RFLM Label (/Port Details) |
| snmpPortId |
type=long access=read-only default=0 |
| speed |
DEPRECATED: 18.12 - This property was never supported. Use vwm.PortSpecifics.etherSpeed instead. type=int default=speed100 minimum=0 maximum=5000 units=mbps enums= 0: notApplicable - N/A (not selectable) 1: speed10 - 10 Mbps 2: speed100 - 100 Mbps |
| terminalLoopbackStatus |
"Interface Terminal Loopback."
type=generic.EnabledDisabled Displayed(tab/group)=Terminal LoopBack Status (/Loop Back) |
| topologyString1 |
First user configurable string allowing a user to
administer the topology of the network.
type=string minimum=0 maximum=255 Displayed(tab/group)=Topology String 1 (/Port Details) |
| topologyString2 |
Second user configurable string allowing a user to
administer the topology of the network.
type=string minimum=0 maximum=255 Displayed(tab/group)=Topology String 2 (/Port Details) |
| tpid |
type=int default=34984 minimum=1536 maximum=65535 Displayed(tab/group)=Tpid (/Port Details) |
| vlanId |
type=int access=read-only minimum=1 maximum=4079 Displayed(tab/group)=Vlan Id (/Userdata) |
| Properties inherited from ManagedObject |
|---|
| actionMask, children-Set, deploymentState, isFaultSquelched, name, objectFullName, selfAlarmed |
| Supported Network Elements | |
|---|---|
| 1830 VWM OSU | |
| Product Specifics | |
| 1830 VWM OSU 8.2 | |
| 1830 VWM OSU 8.3 | |
| 1830 VWM OSU 8.4 | |
| 1830 VWM OSU 8.5 | |
| 1830 VWM OSU 9.0 | |