Overview Package Class Deprecated Help

ethernettunnel
EthernetTunnelEndpoint

The EthernetTunnelEndpoint class defines the configuration for an Ethernet Tunnel Endpoint on a Network Element.

public class EthernetTunnelEndpoint

Properties
accessAdaptQos

type=ethernettunnel.AccessAdaptQosEnum
default=distribute
Displayed(tab/group)=Access Adapt QoS (/Load Sharing)
activeTunnelMembers

type=ethernettunnel.EthTunnelMemberMask
access=read-only
default=none
apsDefectStatus

type=ethernettunnel.APSDefectMask
access=read-only
default=none
Displayed(tab/group)=APS Defect Status (APS)
apsRxPdu

type=long
access=read-only
default=0
Displayed(tab/group)=APS Rx PDU (APS/APS Rx PDU)
apsRxPduBridgedSignal

type=ethernettunnel.ApsPduBridgedSignalEnum
access=read-only
Displayed(tab/group)=Bridged Signal (APS/APS Rx PDU)
apsRxPduProtectionType

type=ethernettunnel.ApsPduProtectionTypeMask
access=read-only
Displayed(tab/group)=Protection Type (APS/APS Rx PDU)
apsRxPduRequestState

type=ethernettunnel.ApsPduRequestStateEnum
access=read-only
default=NR
Displayed(tab/group)=Request/State (APS/APS Rx PDU)
apsRxPduRequestedSignal

type=ethernettunnel.ApsPduRequestedSignalEnum
access=read-only
Displayed(tab/group)=Requested Signal (APS/APS Rx PDU)
apsSwitchoverTime

type=Date
access=read-only
default=0
Displayed(tab/group)=APS Switchover Time (APS)
apsTxPdu

type=long
access=read-only
default=0
Displayed(tab/group)=APS Tx PDU (APS/APS Tx PDU)
apsTxPduBridgedSignal

type=ethernettunnel.ApsPduBridgedSignalEnum
access=read-only
Displayed(tab/group)=Bridged Signal (APS/APS Tx PDU)
apsTxPduProtectionType

type=ethernettunnel.ApsPduProtectionTypeMask
access=read-only
Displayed(tab/group)=Protection Type (APS/APS Tx PDU)
apsTxPduRequestState

type=ethernettunnel.ApsPduRequestStateEnum
access=read-only
default=NR
Displayed(tab/group)=Request/State (APS/APS Tx PDU)
apsTxPduRequestedSignal

type=ethernettunnel.ApsPduRequestedSignalEnum
access=read-only
Displayed(tab/group)=Requested Signal (APS/APS Tx PDU)
endPointSiteId

type=InetAddress
access=read-create
default=0.0.0.0
Displayed(tab/group)=Site ID (/Endpoint)
endPointSiteIdAddrType

type=rtr.InetAddressType
access=read-create
default=ipv4
ethernetTunnelPointer

type=Pointer
access=read-only
Displayed(tab/group)=Ethernet Tunnel (/Ethernet Tunnel Manager)
ethernettunnel.EthernetTunnelPathEndpoint-Set type=Children-Set
globalTunnelId

type=long
access=read-only
mgmtMemberSnmpId

type=long
access=read-only
default=0
netw.PhysicalInterfaceCtp-Set type=Children-Set
pathThreshold

type=int
default=0
minimum=0
maximum=15
Displayed(tab/group)=Operational Path Endpoint Threshold (/Load Sharing)
perFpIngQueuing

type=boolean
default=false
Displayed(tab/group)=Enable Per Forwarding Path Ingress Queue (/Load Sharing)
protectionType The Protection Type parameter specifies the protection mode for the global tunnel and the tunnel endpoints.

type=ethernettunnel.ProtectionType
default=g8031_1to1
Displayed(tab/group)=Protection Type (/Endpoint)
revertTime

type=int
default=0
minimum=0
maximum=720
units=seconds
Displayed(tab/group)=Revert Time (/Endpoint)
revertTimeCountDn

type=long
access=read-only
default=0
units=seconds
Displayed(tab/group)=Revert Time Count Down (/Endpoint)
tunnelEndpointId The Tunnel Endpoint ID parameter specifies an identifier for the tunnel endpoint. The range is 1 to 1024. The number is inherited from the Tunnel ID but it can be changed.

type=int
access=read-create
default=0
minimum=1
maximum=1024
Displayed(tab/group)=Tunnel Endpoint ID (/Endpoint)
 
Overridden Properties
administrativeState

default=portInService
encapType The Encap Type parameter specifies the encapsulation type of the ports that can be used as the member ports for the Path Endpoints of an Ethernet tunnel endpoint.

default=qEncap
holdTimeDown The Hold Time Down (centiseconds) parameter specifies the delay between detecting that the member path is down and reporting the status to the G.8031 protection module. The parameter applies only to member path CCM and not to the member port link state. The parameter applies to both the global tunnel and the tunnel endpoint.

maximum=1000
units=centiseconds
holdTimeUp The Hold Time Up parameter specifies the delay, in deciseconds, used for the hold-timer for associated CC Session up event dampening. The parameter refers to both the global tunnel/ring and the tunnel/ring endpoint.

default=20
maximum=5000
units=deciseconds
isTerminatable

default=true
macAddress The Configured Mac Address parameter assigns a specific MAC address to an Ethernet tunnel endpoint. If this parameter is left at its default value, a default MAC address is assigned by the system from the chassis MAC address pool.

mode

access=read-only
default=access
mtuValue

access=read-only
speed

access=read-only
 
Properties inherited from equipment.Port
accessuplink.EgressQueueStatsConfig-Set, accountingPolicyCapable, accountingPolicyId, accountingPolicyName, accountingPolicyObjectPointer, actualSpeed, collectStats, currentNumberOfChannels, description, displayedName, encapType, equipment.PortEgrHsmdaSchedulerOverride-Set, equipment.PortSchedulerOverride-Set, ethAccessAccountingPolicyObjectPointer, ethAccessCollectStats, etherAccountingPolicyObjectPointer, etherCollectStats, hasConnections, hasUserAssignedMac, holdTimeDown, holdTimeUnits, holdTimeUp, hwMacAddress, intervalNumber, iomType, isConnectionTerminated, isLinkUp, isPortChannelALeaf, isTerminatable, isl2UplinkMode, l2ProfilePointer, linkTrap, loadBalanceAlgorithm, macAddress, memberOfIGH, mirrorStatus, mode, mpr.FlowEntry-Set, mpr.PwAtmLayer-Set, mpr.VlanPort-Set, mptCombiner, mptCombinerImplemented, mptSubrackPointer, mtuValue, neSpecificMtu, networkQueueObjectPointer, networkQueuePolicyCapable, networkQueuePolicyName, numberOfPossibleChannels, operationalMTU, parentSnmpPortId, portBreakout, portCategory, portClass, portEgrHsmdaSchedulerPolicy, portEgrNamedPoolPlcy, portEgrPoolPercentageRate, portHoldTimeDownRemaining, portHoldTimeUpRemaining, portId, portIngrNamedPoolPlcy, portIngrPoolPercentageRate, portName, portRsFecOperMode, portSchedulerPolicyObjectPointer, portStateFPNumber, portStateLicensed, portStateMacChipNumber, portUsage, portUsageType, previousState, radioequipment.RadioPortSpecifics-Set, snmpPortId, specificCardType, specificType, speed, state, ubtListBits, ubtSpeed, uniProfilePointer, unpPortType, upProtocols, userLabel, vlanAutoBind, vwm.OtdrSpecifics-Set
 
Properties inherited from equipment.Equipment
administrativeState, backgroundDiagnosticsFaultReason, backgroundDiagnosticsState, baseMacAddress, cleiCode, compositeEquipmentState, containingEquipmentState, displayedName, equipmentCategory, equipmentState, hardwareClass, hardwareFailureReason, hwFirmwareRevisionStatus, hwIndex, hwName, isEquipmentInserted, isEquipped, isTempSensorAvailable, lockOlcState, manufactureDate, manufacturer, manufacturerBoardNumber, manufacturingAssemblyNo, manufacturingDeviations, manufacturingVariant, oesShelfId, olcState, operationalState, phyShelfClass, phyShelfType, serialNumber, shelfId, siteId, siteName
 
Properties inherited from ManagedObject
actionMask, children-Set, deploymentState, isFaultSquelched, name, objectFullName, selfAlarmed
 
Methods inherited from equipment.Port
getMigrationResult, migrateMode
 
Methods inherited from equipment.Equipment
getDependencyCount
 
Supported Network Elements
7750 SR Supported for all versions
  • Excluded chassis types: 7750-SR1, 7750-SRc12, 7750-SRc4, VSR, VSR-I
7450 ESS Supported for all versions
  • Excluded chassis types: 7450-ESS1
7950 XRS
Product Specifics
7450 ESS 20.0
7450 ESS 21.0
7450 ESS 22.0
7450 ESS 23.0
7450 ESS 24.0
7450 ESS 25.0
7750 SR 20.0
7750 SR 21.0
7750 SR 22.0
7750 SR 23.0
7750 SR 24.0
7750 SR 25.0
7950 XRS (all versions)
7950 XRS 20.0
7950 XRS 21.0
7950 XRS 22.0
7950 XRS 23.0
7950 XRS 24.0
7950 XRS 25.0