| Overview | Package | Class | Deprecated | Help |
| Properties | |
|---|---|
| applyConfiguration |
This field is used for 7250 deployment,
for internal use only.
It is used in the last stage to apply the modification.
DEPRECATED: 11.0 R1 - No longer supported by any NE types supported in SAM type=int default=2 |
| cableLength |
Start from SAM 5.0, this property is only used for 7250 1.0 nodes,
For 7250 2.0 or higher nodes, it is replaced by multiple properties as following:
lineBuildout, lineLength, dbLoss and lineImpedance.
DEPRECATED: 7.0.R4 - Not supported on any product currently managed by SAM. type=tdmequipment.CableLengthType default=133ft Displayed(tab/group)=Cable Length (DS1/E1) |
| clockSource |
Clock source for MPR 9500 ASAP Card
type=tdmequipment.DSXClockSource default=nodeTimed Displayed(tab/group)=Node Timed (DS1/E1) |
| dbGain |
This property shows the number of decibels
the received signal is increased to compensate for loss. This property only applies to a ds1
port configured with a 'long' buildout.
type=int access=read-only default=0 units=dB Displayed(tab/group)=Db Gain (DS1/E1) |
| dbLoss |
This property configures the number of decibels the transmission signal
decreases over the line.This properly only applies to a ds1 port
configured with a 'long' buildout.
type=tdmequipment.DbLossType default=lboNotApplicable Displayed(tab/group)=Db Loss (DS1/E1) |
| ds1PortType |
This property configures the physical port type to 'ds1',
'e1' or 'j1'.
type=tdmequipment.DS1PortType default=ds1 Displayed(tab/group)=Port Type (DS1/E1) |
| framing |
The line frame type
DEPRECATED: 11.0 R1 - No longer supported by any NE types supported in SAM type=tdmequipment.FramingModeType default=unframed |
| incoming15Mins |
PDH PM Incoming 15Mins stats
type=boolean default=false Displayed(tab/group)=Incoming Current 15 Min (DS1/E1/PDH PM) |
| incoming24Hrs |
PDH PM Incoming 24Hrs stats
type=boolean default=false Displayed(tab/group)=Incoming Current 24 Hrs (DS1/E1/PDH PM) |
| lineBuildout |
This property configures the cable buildout length. A ds1 port
has two settings for the DS1 cable buildout: a 'short' setting, for
cable lengths of less than or equal to 655 feet, and a 'long' setting
for cable lengths of greater than 655 feet. This property applies to
copper-cable-based DS1 ports only.
type=tdmequipment.BuildoutType default=short Displayed(tab/group)=Line Buildout (DS1/E1) |
| lineCode |
This variable describes the variety of Zero Code Suppression
used on this interface.
type=tdmequipment.LineCodeType default=b8zs Displayed(tab/group)=Line Code (DS1/E1) |
| lineEncoding |
The value of aluExtDS1PortLineEncoding indicates the Zero Code
Suppression set on the physical T1/E1 port.
type=tdmequipment.LineEncodingType default=b8zs Displayed(tab/group)=Line Encoding (DS1/E1) |
| lineImpedance |
This object configures termination impedance for TDM ports if the line type is E1
type=tdmequipment.LineImpedanceType default=120ohm Displayed(tab/group)=Line Impedance (DS1/E1) |
| lineLength |
This property configures the length of the line (in feet).
This property only applies to a ds1 port configured with a 'short' buildout.
For line lengths longer than 655 feet configure the ds1 port buildout as 'long'.
type=tdmequipment.LineLengthType default=length0To133 Displayed(tab/group)=Line Length (DS1/E1) |
| loopback |
The desired loopback configuration of the interface.
DEPRECATED: 11.0 R1 - No longer supported by any NE types supported in SAM type=tdmequipment.LoopbackType default=disabled |
| mode |
type=tdmequipment.PortModeType access=read-only default=e1 Displayed(tab/group)=Mode (DS1/E1) |
| moduleId |
This field is used for 7250 deployment,
in the last stage to apply the modification on module
DEPRECATED: 11.0 R1 - No longer supported by any NE types supported in SAM type=int access=read-only default=0 |
| outgoing15Mins |
PDH PM Outcoming 15Mins stats
type=boolean default=false Displayed(tab/group)=Outgoing Current 15 Min (DS1/E1/PDH PM) |
| outgoing24Hrs |
PDH PM Outcoming 24Hrs stats
type=boolean default=false Displayed(tab/group)=Outgoing Current 24 Hrs (DS1/E1/PDH PM) |
| pmDS1CDState |
type=int |
| pmE1CDState |
type=int |
| Properties inherited from equipment.PortSpecifics |
|---|
| cardSubType, isPortChannelALeaf, mprFraming, mprLineLength, portClass, portId, snmpPortId, specificCardType, upProtocols |
| Properties inherited from equipment.EquipmentSpecifics |
|---|
| displayedName, lockOlcState, olcState, shelfId, siteId, siteName |
| Properties inherited from ManagedObject |
|---|
| actionMask, children-Set, deploymentState, isFaultSquelched, name, objectFullName, selfAlarmed |