| Overview | Package | Class | Deprecated | Help |
| Properties | |
|---|---|
| cfgRxChan |
This is NFM-P only property. Shows DwdmLaserChannel(tmnxPortDwdmLaserChannel) when tmnxCohOptPortPresRxChan is set to 0.
changed by the system to be equivalent to tmnxPortDwdmLaserChannel.
type=string default=0 (auto) Displayed(tab/group)=Config Rx Channel (Coherent Optical Module) |
| cohOptPortAlarmState |
Indicates the coherent optical alarms currently active on the port.
type=ethernetequipment.CoherentOpticalAlarm access=read-only Displayed(tab/group)=Reported Alarms (Coherent Optical Module) |
| cohOptPortCfgAlarms |
The alarms that are monitored by the coherent optical interface.
If an alarm bit is set, then the corresponding alarm will generate
a raise or clear notification when its state changes.
An unset bit specifies that the alarm corresponding to
the bit will not report on its state transitions.
type=ethernetequipment.CoherentOpticalAlarm default=248 Displayed(tab/group)=Configured Alarms (Coherent Optical Module) |
| cohOptPortCfgCprWinSize |
Specifies the manually configured Carrier Phase Recovery (CPR) window size.
The configured CPR window size is independent of the optimal window size
cohOptPortCprWnSzSrchResult, found by a search using cohOptPortCprWinSizeSearch.
Once the network manager has found an optimal window size in cohOptPortCprWnSzSrchResult,
the network manager has the option to use that value for this property.
type=ethernetequipment.CohOptPortCprWinSize default=32 units=symbols Displayed(tab/group)=Carrier Phase Recovery (CPR) Window Size (Coherent Optical Module) |
| cohOptPortCfgRxChan |
The DWDM ITU channel at which the tunable coherent opticalmodule should operate.
If a value of zero(0) has been specified, tmnxCohOptPortPresRxChan will be
changed by the system to be equivalent to tmnxPortDwdmLaserChannel.
This should be set to the same value as DwdmLaserChannel in most cases,
but may be set to a different value when the received wavelength is different
from the transmitted wavelength.
type=int default=0 Displayed(tab/group)=Coherent Optical Channel (Coherent Optical Module) |
| cohOptPortCfgRxLosThresh |
Specifies the desired average input power LOS (Loss Of Signal) threshold of the interface's received optical signal.
The UNITS millibels (mBm) are units of 0.01 decibel relative to one milliwatt (0 dBm) or dBm multiplied by 100.
The mBm is used when an integer is required. For example -15.21 dBm is equivalent to -1521 mBm.
type=float default=-23.00 minimum=-30.00 maximum=-13.00 units=dBm Displayed(tab/group)=Rx LOS Threshold (Coherent Optical Module) |
| cohOptPortCfgTxPower |
Specifies the desired average output power of the interface's transmitted optical signal
when the port is enabled. The UNITS millibels (mBm) are units of 0.01 decibel relative to
one milliwatt (dBm) or dBm multiplied by 100. The mBm is used when an integer is required.
For example -5.21 dBm is equivalent to -521 mBm.
type=float default=1.00 minimum=-20.00 maximum=3.00 units=dBm Displayed(tab/group)=Tx Target Power (Coherent Optical Module) |
| cohOptPortCfgTxPowerMax |
Indicates the maximum configurable transmit power of the equipped tunable optical module.
type=float access=read-only units=dBm Displayed(tab/group)=Cfg Tx Power Max (Coherent Optical Module) |
| cohOptPortCfgTxPowerMin |
Indicates the minimum configurable transmit power of the equipped tunable optical module.
type=float access=read-only units=dBm Displayed(tab/group)=Cfg Tx Power Min (Coherent Optical Module) |
| cohOptPortCompatMode |
Specifies the optical mode and rate of operation of the Coherent interface
type=ethernetequipment.CohOptPortCompatMode default=longHaul Displayed(tab/group)=Compatibility Mode (Coherent Optical Module) |
| cohOptPortDefectPoints |
Indicates the coherent optical defect points currently active on the port.
type=ethernetequipment.CoherentOpticalDefectPoint access=read-only Displayed(tab/group)=Defect Points (Operational Status) |
| cohOptPortDispCtrlMode |
Specifies the current dispersion compensation mode of the coherent optical module.
When this mode is set to 'automatic(0)', the dispersion setpoint is automatically
determined but under the constraints specified by SweepStart and SweepEnd.
When this mode is set to 'manual(1)', the dispersion setpoint is fixed to the
value specified by Dispersion.
type=ethernetequipment.CohOptPortDispCtrMode default=automatic Displayed(tab/group)=Dispersion Control Mode (Coherent Optical Module) |
| cohOptPortDispSwpEnd |
Specifies the end value for dispersion sweeping on a coherent optical module.
type=int default=2000 minimum=-50000 maximum=50000 units=ps/nm Displayed(tab/group)=Dispersion Sweep End (Coherent Optical Module) |
| cohOptPortDispSwpStart |
Specifies the start value for dispersion sweeping on a coherent optical module.
type=int default=-25500 minimum=-50000 maximum=50000 units=ps/nm Displayed(tab/group)=Dispersion Sweep Start (Coherent Optical Module) |
| cohOptPortManCfgDisp |
Specifies the manually configured dispersion of the coherent optical module.
This parameter is valid when the Dispersion Control Mode is 'manual(1)'.
type=int default=0 minimum=-50000 maximum=50000 units=ps/nm Displayed(tab/group)=Dispersion (Coherent Optical Module) |
| cohOptPortModRxTurnUpStates |
Indicates the completed RX turn-up states of the coherent optical module.
type=ethernetequipment.CohOptPortModRxTurnUpStates access=read-only Displayed(tab/group)=Rx Turn-up States (Operational Status) |
| cohOptPortModState |
Indicates the state of the coherent optical module.
type=ethernetequipment.CohOptPortModState access=read-only Displayed(tab/group)=Module State (Operational Status) |
| cohOptPortModTxTurnUpStates |
Indicates the completed TX turn-up states of the coherent optical module.
type=ethernetequipment.CohOptPortModTxTurnUpStates access=read-only Displayed(tab/group)=Tx Turn-up States (Operational Status) |
| cohOptPortPresRxChan |
Indicates the DWDM ITU channel at which the coherent optical module is operating.
type=int access=read-only Displayed(tab/group)=Operating Channel (Operational Status) |
| cohOptPortRxLosReaction |
The value of cohOptPortRxLosReaction specifies the type of
action that is taken in the event of an RX Loss Of Signal (LOS)
type=ethernetequipment.CohOptPortLosReaction default=none Displayed(tab/group)=Rx LOS Reaction (Coherent Optical Module) |
| cohOptPortRxQMargin |
Indicates the RX Q (quality) Margin, represented in tenths of a dB.
type=float access=read-only units=dB Displayed(tab/group)=Rx Quality Margin (Operational Status) |
| cohOptPortRxSNRXPolar |
Indicates the network RX electrical SNR (Signal-to-Noise Ratio) of X polarization.
type=float access=read-only units=dB Displayed(tab/group)=Rx Signal-to-Noise Ratio X-Polarization (Operational Status) |
| cohOptPortRxSNRYPolar |
Indicates the network RX electrical SNR (Signal-to-Noise Ratio) of Y polarization.
type=float access=read-only units=dB Displayed(tab/group)=Rx Signal-to-Noise Ratio Y-Polarization (Operational Status) |
| cohOptPortSupportsCfgTxPower |
The value of cohOptPortSupportsCfgTxPower indicates whether configurable transmit power is supported by the optical module.
type=boolean access=read-only default=false Displayed(tab/group)=Tx Power Supported (Coherent Optical Module) |
| Properties inherited from equipment.PortSpecifics |
|---|
| cardSubType, isPortChannelALeaf, mprFraming, mprLineLength, portClass, portId, snmpPortId, specificCardType, upProtocols |
| Properties inherited from equipment.EquipmentSpecifics |
|---|
| displayedName, lockOlcState, olcState, shelfId, siteId, siteName |
| Properties inherited from ManagedObject |
|---|
| actionMask, children-Set, deploymentState, isFaultSquelched, name, objectFullName, selfAlarmed |
| Supported Network Elements | |
|---|---|
| 7750 SR |
Supported from 11.0.R1
|
| 7705 SAR Gen 2 | |
| 7705 SAR Hm | |
| 7450 ESS |
Supported from 11.0.R1
|
| 7950 XRS | Supported from 14.0.R4 |
| 7250 IXR | Supported from 20.10.R9 until 21.2.R1Supported from 21.5.R1 |
| Product Specifics | |
| 7250 IXR 20.0 | |
| 7250 IXR 21.0 | |
| 7250 IXR 22.0 | |
| 7250 IXR 23.0 | |
| 7250 IXR 24.0 | |
| 7250 IXR 25.0 | |
| 7450 ESS 20.0 | |
| 7450 ESS 21.0 | |
| 7450 ESS 22.0 | |
| 7450 ESS 23.0 | |
| 7450 ESS 24.0 | |
| 7450 ESS 25.0 | |
| 7705 SAR Gen 2 25.0 | |
| 7705 SAR Hm 20.0 | |
| 7705 SAR Hm 21.0 | |
| 7705 SAR Hm 22.0 | |
| 7705 SAR Hm 23.0 | |
| 7705 SAR Hm 24.0 | |
| 7705 SAR Hm 25.0 | |
| 7750 SR 20.0 | |
| 7750 SR 21.0 | |
| 7750 SR 22.0 | |
| 7750 SR 23.0 | |
| 7750 SR 24.0 | |
| 7750 SR 25.0 | |
| 7950 XRS 20.0 | |
| 7950 XRS 21.0 | |
| 7950 XRS 22.0 | |
| 7950 XRS 23.0 | |
| 7950 XRS 24.0 | |
| 7950 XRS 25.0 | |