|
Properties |
|
cirThreshold |
Specifies the information rate that is acceptable for the test. The result of the test is considered FAIL if the measured value is less than the configured value.
type=int
default=-1
minimum=-1
maximum=10000000
units=kbps
Displayed(tab/group)=CIR Threshold
|
|
criteriaId |
Specifies an ID number for the Acceptance Criteria configuration
type=long
access=read-create
default=0
minimum=1
maximum=8
Displayed(tab/group)=Acceptance Criteria ID
|
|
jitterRaisingThreshold |
Specifies the amount of jitter, in microseconds, that is acceptable for the test. The result of the test is considered FAIL if the measured value is greater than or equal the configured value.
type=int
default=-1
minimum=-1
maximum=2147483000
units=microseconds
Displayed(tab/group)=Jitter Threshold (/Jitter)
|
|
jitterRaisingThresholdIn |
Specifies the amount of jitter, in microseconds, that is acceptable for in-profile packets for the test. The result of the test is considered FAIL if the measured value is greater than or equal to the configured value.
type=int
default=-1
minimum=-1
maximum=2147483000
units=microseconds
Displayed(tab/group)=Jitter Threshold (In) (/Jitter)
|
|
jitterRaisingThresholdOut |
Specifies the amount of jitter, in microseconds, that is acceptable for out-of-profile packets for the test. The result of the test is considered FAIL if the measured value is greater than or equal to the configured value.
type=int
default=-1
minimum=-1
maximum=2147483000
units=microseconds
Displayed(tab/group)=Jitter Threshold (Out) (/Jitter)
|
|
latencyRaisingThreshold |
Specifies the amount of latency, in microseconds, that is acceptable for the test. The result of the test is considered FAIL if the measured value is greater than or equal the configured value.
type=int
default=-1
minimum=-1
maximum=2147483000
units=microseconds
Displayed(tab/group)=Latency Threshold (/Latency)
|
|
latencyRaisingThresholdIn |
Specifies the amount of latency, in microseconds, that is acceptable for in-profile packets for the test. The result of the test is considered FAIL if the measured value is greater than or equal to the configured value.
type=int
default=-1
minimum=-1
maximum=2147483000
units=microseconds
Displayed(tab/group)=Latency Threshold (In) (/Latency)
|
|
latencyRaisingThresholdOut |
Specifies the amount of latency, in microseconds, that is acceptable for out-of-profile packets for the test. The result of the test is considered FAIL if the measured value is greater than or equal to the configured value.
type=int
default=-1
minimum=-1
maximum=2147483000
units=microseconds
Displayed(tab/group)=Latency Threshold (Out) (/Latency)
|
|
lossRaisingThreshold |
Specifies the amount of loss threshold, in 100 thousandth of a percent, that is acceptable for the test. The result of the test is considered FAIL if the measured value is greater than or equal the configured value.
type=int
default=-1
minimum=-1
maximum=10000000
Displayed(tab/group)=Loss Threshold (/Loss Raising)
|
|
lossRaisingThresholdIn |
Specifies the amount of packet loss, in 100-thousandths of a percent, that is acceptable for in-profile packets for the test. The result of the test is considered FAIL if the measured value is greater than or equal to the configured value.
type=int
default=-1
minimum=-1
maximum=10000000
Displayed(tab/group)=Loss Threshold (In) (/Loss Raising)
|
|
lossRaisingThresholdOut |
Specifies the amount of packet loss, in 100-thousandths of a percent, that is acceptable for out-of-profile packets for the test. The result of the test is considered FAIL if the measured value is greater than or equal to the configured value.
type=int
default=-1
minimum=-1
maximum=10000000
Displayed(tab/group)=Loss Threshold (Out) (/Loss Raising)
|
|
pirThreshold |
Specifies the peak information rate that is acceptable for the test. The result of the test is considered FAIL if the measured value is less than the configured value.
type=int
default=-1
minimum=-1
maximum=10000000
units=kbps
Displayed(tab/group)=PIR Threshold
|