Overview Package Class Deprecated Help

mpls
P2MPLspTrace

Represents a P2MP LspTrace' test operations for a single leaf egress node of an P2MP LSP.

public class P2MPLspTrace

Properties
forwardingClass Specifies the forwarding class the LSP trace will use.

type=qos.FcEnum
default=be
Displayed(tab/group)=Forwarding Class (Test Parameters/Test Probe)
initialTimeToLive Specifies the initial outermost label time-to-live value. This enables bypassing the initial (often well known) portion of a path.

type=int
default=1
minimum=1
maximum=255
Displayed(tab/group)=Initial Time To Live (Test Parameters/Test Probe)
leafIpAddr Specifies the Internet address of the egress leaf node of a P2MP LSP Tree. This parameter is mandatory

type=InetAddress
default=0.0.0.0
leafIpAddrType Specifies the type of Internet address stored in

type=rtr.InetAddressType
access=read-only
default=ipv4
maxTimeToLive Specifies the maximum outermost label time-to-live value.

type=int
default=30
minimum=1
maximum=255
Displayed(tab/group)=Maximum Time To Live (Test Parameters/Test Probe)
p2mpDynamicLsp P2MPDynamicLsp defines an LSP as a point-to-multipoint LSP, which contains one or multiple S2L (root-to-leaf) paths and allows the source of multicast traffic to forward packets to one or many multicast receivers over a network.

type=Pointer
access=read-create
default=
Mandatory on create
Displayed(tab/group)=P2MP Dynamic Lsp
p2mpInstance The LSP path to test. May only be specified when testTargetType is lspPath.

type=Pointer
access=read-create
default=
Mandatory on create
Displayed(tab/group)=P2MP Instance
p2mpS2lPath

type=Pointer
access=read-create
default=
Mandatory on create
Displayed(tab/group)=S2L Destination Address
profile Specifies the profile value to be used with the forwarding class specified in forwardingClass.

type=qos.Profile
default=out
Displayed(tab/group)=Forwarding Profile (Test Parameters/Test Probe)
 
Overridden Properties
maxFailures The LSP packet size.

minimum=1
maximum=10
units=octets
packetSize The LSP packet size.

default=137
minimum=128
packetTimeout specifies the size of the OAM Echo message. This parameter is optional and is valid only if tmnxOamPingCtlTestMode has a value of 'sdpPing', 'macPing', 'lspPing', 'vprnPing', 'mfibPing', 'vccvPing', 'icmpPing', 'p2mpLspPing', 'ethCfmLoopback' or 'ethCfmTwoWaySlm'. The minimum, maximum, and default values for the tmnxOamPingCtlTestMode cases are: "The value of tmnxOamPingCtlTimeOut specifies the time-out value, in seconds, to be used during a test run. Timers (with duration configured using the tmnxOamPingCtlTimeOut value) are used in one of two ways during a test run. 1. Per Probe: a timer is started each time a probe is sent. If the timer expires before the probe response arrives, the probe is declared failed. This is the traditional time-out method for a sequence of probes. OR 2. Per Test: a timer is started once per test run, when the last probe of the test run is sent. ANY probe which does not have a response when the timer expires is declared failed. SROS chooses 'Per Probe' or 'Per Test' based on the tmnxOamPingCtlTestMode value. The choice is not configurable. The accepted minimum, maximum, and default values for tmnxOamPingCtlTimeOut depend on tmnxOamPingCtlTestMode, as shown in the following table. The table also shows the timer usage for the test mode. tmnxOamPingCtlTestMode Min Max Def Timer Usage ---------------------- --- --- --- ----------- 'atmPing' 1 10 5 Per Probe 'dnsPing' 1 120 5 Per Probe 'ethCfmLoopback' 1 10 5 Per Probe 'ethCfmTwoWayDelay' 1 10 5 Per Test 'ethCfmTwoWaySlm' 1 10 5 Per Test 'icmpPing' 1 10 5 Per Test 'lspPing' 1 10 5 Per Probe 'macPing' 1 10 5 Per Probe 'mfibPing' 1 100 5 Per Probe 'mtuPing' 1 10 5 Per Probe 'p2mpLspPing' 1 120 10 Per Probe 'sdpPing' 1 10 5 Per Probe 'vccvPing' 1 10 5 Per Probe 'vprnPing' 1 100 5 Per Probe otherwise ......... the value of tmnxOamPingCtlTimeOut is irrelevant

default=1
units=octets
 
Properties inherited from sas.Trace
assurance, maxFailures, maxHistoryRows, packetInterval, packetSize, packetTimeout, packetsToSend, testType, trapGenerationPolicy
 
Properties inherited from sas.Test
accountingFiles, accountingPolicyObjectPointer, aggregatedWith, applicationId, continuousExec, continuously, executionState, fromNodeId, id, lastGeneratedTime, neDeployedTest, nePersistent, neSchedulable, neSchedulableDeployedTest, neSchedulableTest, nmUser, oneTimeValidate, probeHistory, publishTopic, sas.NmThresholdEvent-Set, suppressAccounting, targetIp, testDefinition, testPolicyUsage, testResultStorage, testSuite, testSuiteId, testSuiteTestedEntity, testType, testedEntityName, testedObject, weight
 
Properties inherited from sas.AbstractTest
administrativeState, description, displayedName, failures, globalId, id, lastRunResult, runs, weight
 
Properties inherited from ManagedObject
actionMask, children-Set, deploymentState, isFaultSquelched, name, objectFullName, selfAlarmed
 
Methods inherited from sas.Test
adhocExecuteAndWait, executeAndWait, setNeSchedulableAdminState
 
Methods inherited from sas.AbstractTest
execute, stop
 
Supported Network Elements
7450 ESS
7750 SR
7705 SAR Hm
DC VSC
DC 7850
DC 210
DC VSA8
7210 SAS R Supported from 9.0.R3
7210 SAS T Supported from 9.0.R3
7210 SAS Mxp Supported from 9.0.R3
7950 XRS
7210 SAS S/Sx Supported from 11.0.R6
Product Specifics
7210 SAS Mxp 20.0
7210 SAS Mxp 21.0
7210 SAS Mxp 22.0
7210 SAS Mxp 23.0
7210 SAS Mxp 24.0
7210 SAS Mxp 25.0
7210 SAS R 20.0
7210 SAS R 21.0
7210 SAS R 22.0
7210 SAS R 23.0
7210 SAS R 24.0
7210 SAS R 25.0
7210 SAS S/Sx 20.0
7210 SAS S/Sx 21.0
7210 SAS S/Sx 22.0
7210 SAS S/Sx 23.0
7210 SAS S/Sx 24.0
7210 SAS S/Sx 25.0
7210 SAS T 20.0
7210 SAS T 21.0
7210 SAS T 22.0
7210 SAS T 23.0
7210 SAS T 24.0
7210 SAS T 25.0
7450 ESS 20.0
7450 ESS 21.0
7450 ESS 22.0
7450 ESS 23.0
7450 ESS 24.0
7450 ESS 25.0
7705 SAR Hm 20.0
7705 SAR Hm 21.0
7705 SAR Hm 22.0
7705 SAR Hm 23.0
7705 SAR Hm 24.0
7705 SAR Hm 25.0
7750 SR 20.0
7750 SR 21.0
7750 SR 22.0
7750 SR 23.0
7750 SR 24.0
7750 SR 25.0
7950 XRS 20.0
7950 XRS 21.0
7950 XRS 22.0
7950 XRS 23.0
7950 XRS 24.0
7950 XRS 25.0